A technician checking the inside wall of a concrete water tank with a torch
What our clients rate us

Tank leak repair in Harat Al Zanabiqah Jeddah

Harat Al Zanabiqah sits on Thuwal's northern edge beside the town corniche and the King Abdullah University of Science and Technology campus fence. Houses here are near seawater, and high salinity and constant humidity accelerate corrosion and rust in both metal and concrete tanks.

  • Potable-rated materials

    Linings and disinfectants cleared for drinking water tanks, not general-purpose products.

  • You get the downtime first

    How many hours the tank is out of service, told before we start rather than after we finish.

  • A first-draw flush

    We run the first draw off after refilling, and the tank is not handed back until the water runs clear.

  • Ground and roof tanks

    Villas, apartment blocks and premises that need a written record of each visit.

Why the job is different in Harat Al Zanabiqah

Residential buildings here are close to salt water and tanks face continuous salt spray and permanent moisture exposure. The method is set out in full on how we approach Tank leak repair.

The first reason

Rapid rust in metal tanks from salt air

Metal tanks in the coastal zone rust faster than inland. Salt spray from wind and sea causes accelerated metal corrosion and paint breakdown.

The second reason

Permanent humidity deepens concrete cracks

Moisture here is constant and salt water penetrates concrete causing layer spalling. Freeze-thaw cycles deepen cracks seasonally.

The third reason

Strong winds create lateral pressure and movement

Strong winds from the sea press on elevated tanks and walls, causing movement and cracks in joints and pipes.

The character of Harat Al Zanabiqah

Coastal area: high humidity and salt air through the year

The coastal location means tanks face constant salt and moisture exposure. Repair approach differs from inland and requires salt-resistant materials and more frequent inspection because leaks develop faster.

Before treatment

Where the water leaves decides how it is repaired

A coastal residential quarter on Thuwal's north edge, touching the shoreline on one side and the university campus fence on the other, with the town corniche as a buffer to the sea.

A concrete wall marked with damp and a white salt bloom

Damp and salt on the outside wall

Checking metal corrosion, rust colour and depth reveals impact of salt and coastal moisture on tanks.

A fine crack running across a concrete surface

The kind of crack

Inspecting concrete outer layers for spalling and breakdown determines penetration depth of salt water.

The corner where a concrete floor meets a wall

The wall to floor junction

Checking inlet and outlet pipes and joints that move from wind and lateral pressure.

Water pipes passing through a concrete wall

Pipe entries

Checking constant moisture around tank and exposure to salt air and continuous spray.

A blistered and peeling layer on a concrete surface

The condition of the old lining

Checking tank mounting and stability against lateral pressure from strong winds.

A white plastic water tank standing outside

What the tank is made of

Checking water colour, sediment and salinity affecting corrosion development rate.

How we work

  1. 1

    Inspect and locate the leak

    We close the float valve and the outlet, mark the water level and watch it fall, then check the fittings and the wall beside it. That separates a tank leak from a pipe leak or a float valve that never shuts.

  2. 2

    Drain, clean and dry

    We empty the tank, lift the sediment off the base, wash back to sound concrete and let the surface dry. No repair holds on a damp or dusty face.

  3. 3

    Repair the cracks and the entries

    We cut the crack open, fill it with a non-shrink mortar, inject anything still weeping and rebuild around the pipe sleeve. A joint that moves takes a flexible detail, not a rigid one.

  4. 4

    Refill, test, then sterilise

    We refill, read the level again to confirm the drop has stopped, then sterilise before the water is used, because the tank has been open with tools and hands inside it.

What tank leak repair includes

  • A technician inspecting with a flashlight

    A marked level test

    A reading before and after with everything shut, which establishes that the loss is the tank and not the plumbing.

  • A metal floor drain

    Draining and sediment removal

    Water and silt out of the base, so the floor and the walls can be seen as they really are.

  • A spray nozzle in close detail

    Pressure wash and dry back

    The weak layer and the dust come off, because a repair only holds on sound concrete.

  • A gloved hand applying bait into a joint

    Cracks opened and filled

    The crack is cut open and filled with a non-shrink mortar, and anything still weeping under water pressure is injected.

  • The visit report being written on a clipboard

    Refill and a recorded test

    We refill, read the level again and write the reading down, so the result is not a matter of opinion.

  • A clean kitchen counter after treatment

    Sterilised and back in service

    A wash and a sterilisation once the material has cured, and guidance on running the first fill off before the water is used.

What is different about Thuwal Sub-Municipality

Thuwal sub municipality is a small fishing town on the Red Sea coast at the far northern edge of Jeddah governorate. Its old quarters are closely packed popular and mud built houses on narrow streets, with newer low rise concrete homes from the town's development programme beside them. Sea humidity stays high all year, the fishing harbour and the corniche form its seafront, water arrives by tanker so household tanks are everywhere, and the town sits on Wadi Thuwal, ringed by open ground and by the irrigated green campus of King Abdullah University of Science and Technology.

Questions about this district

Why do our coastal tanks leak more than inland ones?

Salt and high humidity accelerate rust in metals and decay in concrete. Salt water penetrates faster than fresh water.

Does protective coating stop rust in coastal areas?

It slows it but does not stop it. Salt penetrates the coating over time and rust continues beneath.

How often do coastal tanks need repair?

This depends on tank condition and material. Metal tanks in coastal zones may need repair every year or two.

Do we replace or repair a tank if the leak is large?

If the leak is large and the tank is old, replacement may cost less than repeated repairs.

Does strong wind directly cause tank leaks?

Not directly, but it causes movement in the tank and joints, deepening existing cracks.

Does lining with salt-resistant material solve coastal tank problems?

Yes, salt-resistant lining protects against salt-driven leaks. But cracks must be repaired first.

How much does tank leak repair in Harat Al Zanabiqah cost?

It is set after the inspection, because the price follows the type of infestation, the size of the space, how far it has spread and the number of visits it needs. Send a photo and a description on WhatsApp and we will give you an estimate before we reach Harat Al Zanabiqah.

Other services in Harat Al Zanabiqah

Other services we provide to residents of Harat Al Zanabiqah.

All services

Need tank leak repair in Harat Al Zanabiqah? Tell us what you saw and we will tell you what it needs

We reach Harat Al Zanabiqah at a time we agree, and you get the full cost before we start.

Call now +966 57 336 7012 WhatsApp