A technician washing the inside wall of a water tank with a pressure hose

Water tank cleaning in Al Hamra Jeddah

Al Hamra is an established upmarket quarter on the Red Sea Corniche, where salt laden air and high year round humidity attack tanks relentlessly. Interiors rust faster than inland, salt deposits form even on expensive villa tanks, and metal lids corrode from the edges inward at startling speed. The water itself may taste faintly salty even when the main supply is fresh.

Call now Message us on WhatsApp

Potable-rated materials

Linings and disinfectants cleared for drinking water tanks, not general-purpose products.
You get the downtime first

How many hours the tank is out of service, told before we start rather than after we finish.
A first-draw flush

We run the first draw off after refilling, and the tank is not handed back until the water runs clear.
Ground and roof tanks

Villas, apartment blocks and premises that need a written record of each visit.

Why the job is different in Al Hamra

Coastal tanks in Al Hamra rust internally three times faster than any inland district does, and salt deposits form on walls continuously even when no seawater visibly enters. The method is set out in full on how we approach Water tank cleaning.

The first reason

Airborne salt and internal corrosion

Sea air carries microscopic salt particles that enter vents and hairline fractures. These salts deposit on tank walls and trigger rust on any iron pipework inside, even painted pipes, spreading inward from the points where saltwater touches metal.

The second reason

Lining and metal cover deterioration

High humidity causes rapid corrosion of metal lids from edges and corners inward. Plastic linings weaken from salt and concentrated ultraviolet radiation on the rooftop, developing hairline cracks within one to three years of installation.

The third reason

Algae and salt crusts

Intense rooftop sunlight and constant moisture drive algae growth at alarming speed. Salt deposits trap algae to walls, making cleaning difficult without industrial strength chemicals that may harm the lining.

Al Hamra on the map

Al Hamra sits about 3.5 km from Al Andalus and about 3.5 km from Mushrifah.

Open in Google Maps

Before treatment

The condition of the tank decides the method

The district runs between the Corniche and Madinah Road facing the King Fahd Fountain, and the moisture carried from the sea penetrates every street breeze and every rooftop surface without pause.

Fine brown sediment beneath shallow water

The layer on the floor

Salt crusts coat the floor of coastal tanks in white or tan layers, and salty water leaves crystals so small they do not dissolve under pressure washing alone without chemical help.

Light and algae

Green and black algae grow rapidly in continuous light and moisture, and salt preserves them and makes them far more resistant to ordinary scrubbing.

A damp concrete wall carrying a dark deposit

The deposit on the wall

Tank walls become white and rough from salt deposits and algae, and this layer needs vigorous scrubbing and concentrated disinfectant to remove.

A concrete surface with a fine hairline crack

The lining and hairline cracks

Hairline cracks in linings appear from salt and ultraviolet radiation, and salt entering through these cracks triggers fast internal rusting of any metal.

The lid of a water tank on a building roof

The lid and the access hatch

Metal caps rust from edges and corners inward where humidity pools, and vent openings are weakened by salt and moisture and may need replacement.

A plastic pipe leaving the exterior wall of a building

The vent and the overflow pipe

Vent openings and overflow pipes clog with salt and algae, and drainage becomes sluggish because mineral deposits shrink the opening diameter.

How we work

1
Inspect before the drain

Tank type and material, the condition of the lining, the depth of the sediment, the lid and the vent, and where the drained water will go. We agree the window without supply before anything is opened.
2
Drain, then lift the sludge

The water leaves through the outlet, then the layer beneath it is taken out by hand and by suction. That layer is the reason for the visit, not the water that ran out ahead of it.
3
High pressure wash

Walls, floor and the joint where they meet, with a brush wherever the film resists, then the wash water is taken out completely so nothing we lifted settles again.
4
Disinfect and put back in service

Disinfectant over every internal surface, left for its contact time and then rinsed out, followed by the refill, a first draw off at the taps, and a report on what was inside the tank.

What water tank cleaning includes

An inspection before the valve

Tank type, lining condition, depth of sediment, lid and vent, recorded before any water leaves.
Full drain and sediment removal

The water through the outlet, and the layer below it by hand and by suction until the floor itself is showing.
Pressure washing walls and floor

High pressure across the surfaces and corners, and a brush on anything water alone will not lift.
Disinfection after the wash

A disinfectant intended for drinking water tanks, named to you before it is used, left for its contact time and then rinsed out.
Refill and the first draw off

We refill, run the taps so the new water moves through the pipework, and tell you when it is ready to use.
A report and the next date

What was inside the tank, anything on the lid or the lining that needs repair, and a sensible date for the next clean.

The character of Al Hamra

Coastal area: high humidity and salt air through the year

A coastal setting means the tank endures airborne salt and humid air through every season. Internal rust and salt deposits accelerate tank decay, and lids and pipes need extra protection to survive the salt load.

Questions about this district

Is salty taste in the water normal living on the coast?

Taste may come from salt deposited inside the tank by sea air, or from old corroded iron pipes. Regular cleaning and monitoring of the internal surface are essential to identify which.

Why do tank lids rust at such terrifying speed here?

Airborne salt, high humidity and intense sun create a perfect rust environment. Metal lids need strong protective coatings and regular inspection cycles to prevent rust from penetrating the seal.

Will a plastic tank lining survive the salt and humidity?

Linings degrade from salt exposure and concentrated ultraviolet radiation on rooftops. After one to three years hairline cracks may develop and need repair work.

Do coastal tanks need cleaning more often than inland districts?

Far more often. Salt, humidity and algae accumulate rapidly, and cleaning every two to three months is necessary to maintain water quality in this climate.

Can sudden pressure loss be salt blocking the pipes?

Yes. Salt deposits inside pipes gradually clog the channels. Pipe inspection as part of service is essential in coastal areas to catch blockages before they worsen.

Should we add extra protection to coastal tanks?

Yes. Strong protective coating on lids and pipes significantly reduces damage. Shielding openings from direct sea air and humidity extends tank life considerably.

How much does water tank cleaning in Al Hamra cost?

It is set after the inspection, because the price follows the type of infestation, the size of the space, how far it has spread and the number of visits it needs. Send a photo and a description on WhatsApp and we will give you an estimate before we reach Al Hamra.