Water tank sterilization in Bani Malik Jeddah
Bani Malik is an old popular quarter that was once a village outside the Jeddah wall, housing shops, car repair workshops and mixed residential buildings. Tanks here are exposed to dust and sand from nearby roads and heavy workshop traffic. Water needs regular sterilization because tanks accumulate sediment and algae quickly.
-
Potable-rated materials
Linings and disinfectants cleared for drinking water tanks, not general-purpose products.
-
You get the downtime first
How many hours the tank is out of service, told before we start rather than after we finish.
-
A first-draw flush
We run the first draw off after refilling, and the tank is not handed back until the water runs clear.
-
Ground and roof tanks
Villas, apartment blocks and premises that need a written record of each visit.
Why the job is different in Bani Malik
Tanks in Bani Malik become contaminated quickly from sand and dust due to the quarter's proximity to main roads and industrial workshops. The method is set out in full on how we approach Water tank sterilization.
Tanks in shops and workshops
Market stalls, restaurants and repair shops place tanks on exposed roofs exposed to sand and hot winds. Water becomes unusable quickly and sterilization requires more frequent cycles.
Sediment and algae from hard water
Jeddah's water is hard and leaves thick sediment on tank walls. Algae grows rapidly in exposed and damp tanks.
Long and complex pipelines in residential buildings
Older residential buildings in Bani Malik have complex and long pipe runs. Distant pipes need high-pressure flushing to clean and sterilize from the furthest point.
Landmarks of Bani Malik
Bani Malik lies between King Fahd Road and Haramain Road, with the famous Bani Malik market marking the commercial centre. Access routes run through petrol stations and car repair workshop clusters spread across the district.
- Bani Malik Street
- Bani Malik Market
- Palestine Street
- King Fahd Road
- Al Noor Mosque
- Bani Malik Park
What we read inside the tank before anything starts
A historic popular quarter on King Fahd Road and Haramain Road, containing the famous Bani Malik market, car repair workshops and residential buildings on the site of the old Nazlat Bani Malik village.
Sediment on the floor
Heavy sediment accumulates on tank floors from hard water and dust carried from workshops and roads.
The slime film on the wall
Green and brown algae grow on walls of exposed tanks subject to light and moisture.
Light and heat
Main pipes and long branches require high water pressure to clean from the furthest point in residential buildings.
The lining and any cracking
Chlorine smell and sterilant residue remains after treatment and needs repeated flushing from furthest lines.
The lid and the openings
Bacteria and airborne contaminants enter exposed tanks easily.
What shows up at the tap
Tanks in shops and workshops need regular inspection for water loss and cracks because they endure high pressure cycling.
How we work
-
1
Inspect and record the condition
We open the hatch and work through what the tank is made of and how big it is, how deep the sediment lies, the state of the lining, whether the lid and the overflow seal, and whether there is a crack that has to be repaired before any sterilizing.
-
2
Drain and lift the sediment out
The water goes out, then the silt and sand are lifted off the floor by suction rather than pushed toward the outlet, because pushing them sends them into the house pipework and the heater.
-
3
High pressure wash
Walls, floor, corners and the area around the outlet, until the slime film is completely gone. This is the step that makes the sterilizing after it mean anything.
-
4
Sterilize, rinse, then return to service
The sterilizing agent goes onto the walls, the floor and the underside of the lid and is left for its contact time, then we rinse, refill and run the furthest tap until the whole line is clear.
What water tank sterilization includes
-
A recorded inspection
Material, capacity, sediment depth, the state of the lining, the lid and the overflow, all before any work begins.
-
Draining and sediment removal
The water out, and the silt and sand lifted off the floor instead of being pushed into the outlet and the house pipework.
-
High pressure washing
Walls, corners and around the outlet, until the biofilm that no disinfectant penetrates has gone.
-
Sterilizing the internal surfaces
A sterilizing agent meant for drinking water tanks, applied to the walls, the floor and the underside of the lid, and left for its contact time.
-
Line flush and aftercare
Rinse, refill and a flush from the furthest tap, when the water is usable again, and what to change in the filter afterwards.
-
The next cycle
We agree the right interval for your tank from how it is filled, how much sun it takes and the condition of the lid.
What is different about Al Sharafiyah Sub-Municipality
The Al Sharafiyah sub municipality runs across central Jeddah from Al Ruwais near the Corniche eastwards through Al Sharafiyah, Al Wurud and Bani Malik to Al Naseem at the Haramain Road. It was among the first areas to grow beyond the old wall, and it is dominated by dense apartment blocks over shops along King Fahd Road and Palestine Street, with old popular quarters, the Bani Malik market, car workshops and storerooms. Ageing buildings, worn drainage and the refuse of restaurants and markets make cockroaches and rodents the most persistent pests, and humidity rises towards the sea.
Questions about this district
Why do tanks get dirty faster in Bani Malik than other areas?
Proximity to main roads and workshops raises airborne dust and sand; exposed tanks are vulnerable to airborne contaminants and wind-blown particles.
Is one sterilization enough for a whole year?
It may not be. In commercial and workshop areas, repeating sterilization every three or four months is better.
Do old water pipes affect water quality after sterilization?
Yes. If pipes are old and rusted, water can become recontaminated quickly even after sterilization.
How do we handle tanks in workshops that consume large volumes of water?
Workshops consume water quickly and refill tanks frequently, so sterilization needs higher concentration and more frequent monitoring.
Is tank sediment removal necessary before sterilization?
Absolutely. If sediment and algae remain, the sterilizing agent cannot reach all surfaces and will not work efficiently.
Is water safe to drink immediately after sterilization and flushing?
Yes. After complete flushing from the furthest tap and removal of sterilant smell, the water is safe to drink and cook with.
How much does water tank sterilization in Bani Malik cost?
It is set after the inspection, because the price follows the type of infestation, the size of the space, how far it has spread and the number of visits it needs. Send a photo and a description on WhatsApp and we will give you an estimate before we reach Bani Malik.
Nearby districts we cover
Other services in Bani Malik
Other services we provide to residents of Bani Malik.
-
Water tanks
Water tank cleaning
-
Water tanks
Water tank sealing
-
Water tanks
Tank leak repair
-
Residential
Cockroach control
Need water tank sterilization in Bani Malik? Tell us what you saw and we will tell you what it needs
We reach Bani Malik at a time we agree, and you get the full cost before we start.