A technician checking the inside wall of a concrete water tank with a torch
What our clients rate us

Tank leak repair in Al Shamiyah Al Jadid Makkah

Al Shamiyah Al Jadid is one of the largest modern residential projects in Jeddah, the Crown Prince First scheme on the Al Laith road west. The district is very new, buildings and tanks are modern, but tanks face high pressure from heavy use. Streets are wide and houses and buildings orderly. Leaks are rare but when they occur they stem from construction defects or pressure stress.

  • Potable-rated materials

    Linings and disinfectants cleared for drinking water tanks, not general-purpose products.

  • You get the downtime first

    How many hours the tank is out of service, told before we start rather than after we finish.

  • A first-draw flush

    We run the first draw off after refilling, and the tank is not handed back until the water runs clear.

  • Ground and roof tanks

    Villas, apartment blocks and premises that need a written record of each visit.

Why the job is different in Al Shamiyah Al Jadid

Buildings are very new and tanks are modern reinforced concrete or stainless steel. Pressure on tanks is high due to heavy consumption and high housing density. The method is set out in full on our Tank leak repair service.

The first reason

Modern tanks under high pressure

Tanks are reinforced concrete or stainless steel and very new. But the resident population is large and consumption is heavy. Continuous pressure on tanks may cause cracks at joints or walls.

The second reason

Modern apartment buildings and villas

The district contains modern apartment blocks and residential villas. Each building has its own tank. Shared tanks in apartment blocks are large, individual villa tanks smaller.

The third reason

Heavy use and high housing density

The project is new and residents are settling rapidly. Daily consumption is very heavy and pressure on tanks continues all day.

Al Shamiyah Al Jadid on the map

Al Shamiyah Al Jadid sits about 3 km from Al Shubaikah Al Jadid and about 4 km from Harat Al Bab Al Jadid.

Open in Google Maps
Before treatment

Where the water leaves decides how it is repaired

A modern housing scheme south of Jeddah on the Al Laith road, the westernmost of the southern schemes near the Fifth Ring Road and Haram boundary on the Al Laith road. Modern apartment blocks and villas on wide streets with commercial areas and a planned leisure centre with gardens between the Al Laith road and the Non Muslims bypass.

A concrete wall marked with damp and a white salt bloom

Damp and salt on the outside wall

Level drop testing is faster in new tanks because pressure is regular and the tank is tightly sealed.

A fine crack running across a concrete surface

The kind of crack

Inspection of pipe entry and exit points focuses on modern fittings and high pressure may cause leaks there.

The corner where a concrete floor meets a wall

The wall to floor junction

Small cracks in concrete walls may appear from continuous pressure or original construction defects.

Water pipes passing through a concrete wall

Pipe entries

Water quality is good here and leaks do not cause algae or bacterial growth easily, but cleaning is important for water quality.

A blistered and peeling layer on a concrete surface

The condition of the old lining

Leak location is usually at joints or entry points rather than in the tank walls themselves.

A white plastic water tank standing outside

What the tank is made of

Leaks in new tanks are rare but when they occur stem from pressure or defects, and repair is quick and simple.

How we work

  1. 1

    Inspect and locate the leak

    We close the float valve and the outlet, mark the water level and watch it fall, then check the fittings and the wall beside it. That separates a tank leak from a pipe leak or a float valve that never shuts.

  2. 2

    Drain, clean and dry

    We empty the tank, lift the sediment off the base, wash back to sound concrete and let the surface dry. No repair holds on a damp or dusty face.

  3. 3

    Repair the cracks and the entries

    We cut the crack open, fill it with a non-shrink mortar, inject anything still weeping and rebuild around the pipe sleeve. A joint that moves takes a flexible detail, not a rigid one.

  4. 4

    Refill, test, then sterilise

    We refill, read the level again to confirm the drop has stopped, then sterilise before the water is used, because the tank has been open with tools and hands inside it.

What tank leak repair includes

  • A technician inspecting with a flashlight

    A marked level test

    A reading before and after with everything shut, which establishes that the loss is the tank and not the plumbing.

  • A metal floor drain

    Draining and sediment removal

    Water and silt out of the base, so the floor and the walls can be seen as they really are.

  • A spray nozzle in close detail

    Pressure wash and dry back

    The weak layer and the dust come off, because a repair only holds on sound concrete.

  • A gloved hand applying bait into a joint

    Cracks opened and filled

    The crack is cut open and filled with a non-shrink mortar, and anything still weeping under water pressure is injected.

  • The visit report being written on a clipboard

    Refill and a recorded test

    We refill, read the level again and write the reading down, so the result is not a matter of opinion.

  • A clean kitchen counter after treatment

    Sterilised and back in service

    A wash and a sterilisation once the material has cured, and guidance on running the first fill off before the water is used.

The character of Al Shamiyah Al Jadid

New development: ongoing construction and vacant plots between the homes

A very new modern district means tanks are new and made of the best materials. But high housing density and heavy use put continuous pressure on tanks. Repair is fast and easy but prevention is key.

Questions about this district

Why a leak in a new tank?

May be due to a construction defect or material fault. High pressure and heavy use may expose defects quickly.

Do stainless steel tanks never leak?

Rarely. But leaks may come from joints or construction defects in the original build.

Does high pressure cause leaks?

Yes. Continuous pressure on tank walls may cause small cracks at joints or walls.

How often should a tank be inspected in Al Shamiyah Al Jadid?

Once yearly is enough for new tanks. But if you notice unusual water bill increases, inspection is urgent.

Does a new tank need regular cleaning?

Yes. Even new tanks need annual cleaning to remove algae, sediment and bacteria.

How long does modern tank repair take?

Faster than old ones. New tanks are easier to access and repair may take just one day.

How much does tank leak repair in Al Shamiyah Al Jadid cost?

It is set after the inspection, because the price follows the type of infestation, the size of the space, how far it has spread and the number of visits it needs. Send a photo and a description on WhatsApp and we will give you an estimate before we reach Al Shamiyah Al Jadid.

Other services in Al Shamiyah Al Jadid

Other services we provide to residents of Al Shamiyah Al Jadid.

All services

Need tank leak repair in Al Shamiyah Al Jadid? Tell us what you saw and we will tell you what it needs

We reach Al Shamiyah Al Jadid at a time we agree, and you get the full cost before we start.

Call now +966 57 336 7012 WhatsApp