Tank leak repair in Al Sarawat Jeddah
Al Sarawat is an industrial district at the far south of Jeddah on the western side of Al Khumrah, between the Industrial City and the southern corniche. Large warehouses and workshops here draw heavy water supply and tanks face salt-laden sea wind and intense heat. Pipes run through desert and sandy ground at varying depths.
-
Potable-rated materials
Linings and disinfectants cleared for drinking water tanks, not general-purpose products.
-
You get the downtime first
How many hours the tank is out of service, told before we start rather than after we finish.
-
A first-draw flush
We run the first draw off after refilling, and the tank is not handed back until the water runs clear.
-
Ground and roof tanks
Villas, apartment blocks and premises that need a written record of each visit.
Why the job is different in Al Sarawat
The area is desert and sandy ground with unstable soil. Tanks sit in wide open spaces. Sandy soil shifts with wind and rare rains carve channels beneath the surface. The method is set out in full on the full Tank leak repair page.
Salt-laden wind from the sea and external corrosion
The sea is very close and winds carry salt and moisture. Metal tanks corrode rapidly from the outside and iron pipes rust from the salty air.
Intense heat and direct sun exposure
Warehouses sit in open areas and tanks face direct sun from dawn to dusk. Plastic and fibreglass crack and joints loosen from rapid expansion.
Sandy soil movement and underground stress
Pipes lie in unstable sandy ground. Shifting soil and rare heavy rains wash channels beneath, causing pipes to bend and break. Long runs from tank to warehouse increase leak risk.
Al Sarawat on the map
Al Sarawat sits about 4.5 km from Al Saruriyah and about 6 km from Al Taawun.
Open in Google MapsWhere the water leaves decides how it is repaired
An industrial district at the far south of Jeddah on the western side of Al Khumrah, with large warehouses, workshops, scattered villas and wide open plots, between the Industrial City to the north and the southern corniche to the west, with Al Laith Road nearby.
Damp and salt on the outside wall
Float valve and outlet inspection requires closing both and watching slow or rapid decline in large tanks at distance.
The kind of crack
Iron and copper pipe inspection focuses on rust from salt moisture and exposed connections to sea air.
The wall to floor junction
Tank body inspection searches for cracks from rapid thermal expansion and external salt corrosion.
Pipe entries
Moisture around the tank may come from leakage or natural humidity near the sea and high water table.
The condition of the old lining
Sediment in the tank signals past leakage or seawater intrusion through sandy soil, both speeding internal corrosion.
What the tank is made of
Pipes beneath sand leak from soil movement, bending and pressure, so detection requires isolated testing of each run to pinpoint the exact leak location.
How we work
-
1
Inspect and locate the leak
We close the float valve and the outlet, mark the water level and watch it fall, then check the fittings and the wall beside it. That separates a tank leak from a pipe leak or a float valve that never shuts.
-
2
Drain, clean and dry
We empty the tank, lift the sediment off the base, wash back to sound concrete and let the surface dry. No repair holds on a damp or dusty face.
-
3
Repair the cracks and the entries
We cut the crack open, fill it with a non-shrink mortar, inject anything still weeping and rebuild around the pipe sleeve. A joint that moves takes a flexible detail, not a rigid one.
-
4
Refill, test, then sterilise
We refill, read the level again to confirm the drop has stopped, then sterilise before the water is used, because the tank has been open with tools and hands inside it.
What tank leak repair includes
-
A marked level test
A reading before and after with everything shut, which establishes that the loss is the tank and not the plumbing.
-
Draining and sediment removal
Water and silt out of the base, so the floor and the walls can be seen as they really are.
-
Pressure wash and dry back
The weak layer and the dust come off, because a repair only holds on sound concrete.
-
Cracks opened and filled
The crack is cut open and filled with a non-shrink mortar, and anything still weeping under water pressure is injected.
-
Refill and a recorded test
We refill, read the level again and write the reading down, so the result is not a matter of opinion.
-
Sterilised and back in service
A wash and a sterilisation once the material has cured, and guidance on running the first fill off before the water is used.
The character of Al Sarawat
Industrial area: workshops, warehouses and loading yards
Al Sarawat is an industrial desert zone with unstable sandy soil and tanks sit in wide open spaces. Sea salt and intense heat cause rapid metal corrosion, so repair must account for the saline environment and soil movement beneath.
Questions about this district
Why do tanks in Al Sarawat corrode faster?
Salt and moisture from the nearby sea cause rapid rust on metal tanks and pipes. Intense heat accelerates corrosion and leakage.
Does the sea cause direct leakage or is it internal tank failure?
The sea does not leak directly but salt corrodes metals from outside. Detection requires closing the float valve and outlet and watching level decline to identify whether the leak is in the tank or pipes.
Can pipes beneath sand be repaired without extensive digging?
If the crack is small, we may repair it without deep excavation. But in unstable sandy soil, we may need to dig and reset the pipe properly to prevent further movement.
Does lining hold up against sea salt and moisture?
Interior lining stops seepage but salt may find a new path. Repair must come first and the tank may need protective external coating.
How do we handle tanks far from the main building?
Distant tanks are exposed to soil movement and piping strain. We test each pipe section by closing valves at different points.
Is pipe replacement simpler than repair in sandy areas?
Yes. In unstable sandy soil, replacement may be faster and cheaper than repairing at multiple depths.
How much does tank leak repair in Al Sarawat cost?
It is set after the inspection, because the price follows the type of infestation, the size of the space, how far it has spread and the number of visits it needs. Send a photo and a description on WhatsApp and we will give you an estimate before we reach Al Sarawat.
Nearby districts we cover
Other services in Al Sarawat
Other services we provide to residents of Al Sarawat.
-
Water tanks
Water tank cleaning
-
Water tanks
Water tank sterilization
-
Water tanks
Water tank sealing
-
Residential
Cockroach control
Need tank leak repair in Al Sarawat? Tell us what you saw and we will tell you what it needs
We reach Al Sarawat at a time we agree, and you get the full cost before we start.