A technician checking the inside wall of a concrete water tank with a torch
What our clients rate us

Tank leak repair in Muad Makkah

Muad is a mixed quarter of villas and apartment buildings lying between Al Khadra and Al Sharai just outside the Haram boundary. The tanks here vary widely in age and type, from old rooftop tanks to modern pump systems. Leaks may arise from fluctuating pressure and weak filtration in the local network.

  • Potable-rated materials

    Linings and disinfectants cleared for drinking water tanks, not general-purpose products.

  • You get the downtime first

    How many hours the tank is out of service, told before we start rather than after we finish.

  • A first-draw flush

    We run the first draw off after refilling, and the tank is not handed back until the water runs clear.

  • Ground and roof tanks

    Villas, apartment blocks and premises that need a written record of each visit.

Why the job is different in Muad

The area is dense with relatively modern residential projects and tanks vary widely in age. Some villas hold very old tanks and others have modern systems. The method is set out in full on the full Tank leak repair page.

The first reason

Older villas have rusted metal tanks

The oldest villas in Muad have old metal or galvanised iron tanks mounted on the roof. Rust eats through the tank body and causes fine holes that slowly widen.

The second reason

Pumping from deep wells stresses pipes

Some villas and buildings have pump systems drawing from deep wells, and high pressure strains pipes and fittings. Joints loosen under repeated stress.

The third reason

The local water network is unstable and pressure fluctuates

Al Qadisiyah Road and nearby streets have old public water lines with erratic pressure. The fluctuation causes stress on private tanks and pipes.

Muad on the map

Muad sits about 2 km from Sharai and about 2 km from Salam.

Open in Google Maps
Before treatment

Where the water leaves decides how it is repaired

A mixed district running between Al Khadra and Al Sharai just outside the Haram boundary, containing villas and buildings along Al Qadisiyah Road, with several mosques including Al Aqeel, Hunayn and Sheikh Nasser Al Assaf, and Al Sharai Park on its northern edge.

A concrete wall marked with damp and a white salt bloom

Damp and salt on the outside wall

The level-hold test is done by closing the float and outlet valve and watching water fall during normal use or complete standby.

A fine crack running across a concrete surface

The kind of crack

Visual inspection of the tank and pipes reveals rust, moisture and dents in metal or cracks in fibreglass.

The corner where a concrete floor meets a wall

The wall to floor junction

A pressure gauge test tells us if network pressure is too high and stressing the pipes.

Water pipes passing through a concrete wall

Pipe entries

Joints and fittings between pipes and tank are checked closely because they loosen under pressure.

A blistered and peeling layer on a concrete surface

The condition of the old lining

Moisture around the tank base and beneath pipes points to the leak location precisely.

A white plastic water tank standing outside

What the tank is made of

White salt and mineral deposits on metal pipes point to old rust and persistent seepage.

How we work

  1. 1

    Inspect and locate the leak

    We close the float valve and the outlet, mark the water level and watch it fall, then check the fittings and the wall beside it. That separates a tank leak from a pipe leak or a float valve that never shuts.

  2. 2

    Drain, clean and dry

    We empty the tank, lift the sediment off the base, wash back to sound concrete and let the surface dry. No repair holds on a damp or dusty face.

  3. 3

    Repair the cracks and the entries

    We cut the crack open, fill it with a non-shrink mortar, inject anything still weeping and rebuild around the pipe sleeve. A joint that moves takes a flexible detail, not a rigid one.

  4. 4

    Refill, test, then sterilise

    We refill, read the level again to confirm the drop has stopped, then sterilise before the water is used, because the tank has been open with tools and hands inside it.

What tank leak repair includes

  • A technician inspecting with a flashlight

    A marked level test

    A reading before and after with everything shut, which establishes that the loss is the tank and not the plumbing.

  • A metal floor drain

    Draining and sediment removal

    Water and silt out of the base, so the floor and the walls can be seen as they really are.

  • A spray nozzle in close detail

    Pressure wash and dry back

    The weak layer and the dust come off, because a repair only holds on sound concrete.

  • A gloved hand applying bait into a joint

    Cracks opened and filled

    The crack is cut open and filled with a non-shrink mortar, and anything still weeping under water pressure is injected.

  • The visit report being written on a clipboard

    Refill and a recorded test

    We refill, read the level again and write the reading down, so the result is not a matter of opinion.

  • A clean kitchen counter after treatment

    Sterilised and back in service

    A wash and a sterilisation once the material has cured, and guidance on running the first fill off before the water is used.

The character of Muad

Mixed district: shops at street level with homes above them

Muad is a mixed quarter of old villas and modern buildings with widely varied tanks and pipe systems. Repair must account for the difference between old metal tanks and modern units, and the various pump and network configurations.

Questions about this district

Why do metal tanks in old villas leak more than modern fibreglass tanks?

Metal rusts and corrodes inside and out. Fibreglass does not react with water or salt. Old metal tanks need urgent repair or replacement.

Does a pump system from a well cause more leaks than the public network?

Yes. Pumping raises pressure significantly and pipes and fittings bear higher stress. Joints loosen or pipes crack easily.

Can an old metal tank be repaired or must it be replaced?

If rust is confined to one area, we repair and line it. If rust is widespread across the body, replacement is better.

Are fibreglass tank leaks rarer than copper pipe leaks?

Fibreglass tanks rarely leak. The problem usually lies in metal joints and fittings between the pipe and tank.

How do we manage high pressure from a pump system?

We inspect pipes for slow leaks. We unscrew suspect fittings, clean them and fit new couplings or heavy thread tape.

Does a small leak from a well pump cause bigger problems than one in a flat?

Yes. The well and pump can create very high pressure and even a small leak may spread quickly. Regular monitoring is essential.

How much does tank leak repair in Muad cost?

It is set after the inspection, because the price follows the type of infestation, the size of the space, how far it has spread and the number of visits it needs. Send a photo and a description on WhatsApp and we will give you an estimate before we reach Muad.

Nearby districts we cover

Other services in Muad

Other services we provide to residents of Muad.

All services

Need tank leak repair in Muad? Tell us what you saw and we will tell you what it needs

We reach Muad at a time we agree, and you get the full cost before we start.

Call now +966 57 336 7012 WhatsApp