A technician applying a lining coat to the inner wall of an emptied water tank
What our clients rate us

Water tank sealing in Al Husayniyah Makkah

Al Husayniyah is a mixed zone between old farmland and new housing, and tanks here face dual challenges. High humidity from the wadi and nearby groundwater cause leaks from floor and walls. Unstable soil around new buildings adds stress to old tanks.

  • Potable-rated materials

    Linings and disinfectants cleared for drinking water tanks, not general-purpose products.

  • You get the downtime first

    How many hours the tank is out of service, told before we start rather than after we finish.

  • A first-draw flush

    We run the first draw off after refilling, and the tank is not handed back until the water runs clear.

  • Ground and roof tanks

    Villas, apartment blocks and premises that need a written record of each visit.

Why the job is different in Al Husayniyah

Tanks here face high humidity from Wadi Uranah and nearby wet soil, causing hydrostatic pressure from outside the tank. The method is set out in full on what Water tank sealing involves.

The first reason

Wadi humidity and groundwater pressure

Wadi Uranah crosses the district and raises groundwater level. Buried or semi-buried tanks face water pressure from outside year-round.

The second reason

New housing on old farmland

The district shifted rapidly from farmland to housing schemes. New foundations and modern tanks were laid on unstable soil with naturally high moisture retention.

The third reason

Mix of old and new tanks

Old farm-era tanks sit beside new building tanks. The old ones were not designed to withstand high humidity and hydrostatic pressure.

Al Husayniyah on the map

Al Husayniyah sits about 3 km from Al Awali and about 6 km from Al Naseem.

Open in Google Maps
Before treatment

What we read before any material is opened

A mixed zone of old farmland and orchards converted into housing schemes, stretching behind Al Awali towards Jabal Kasab and Wadi Malakan on the Taif Al Hada road.

A fine crack running through a concrete wall

Cracking in the wall

Floor leaks are the primary cause due to high groundwater pressure from below.

The junction of a concrete floor and wall inside an empty tank

The floor to wall joint

Wall cracks on lower sections and corners appear because groundwater presses from all sides.

A coating flaking away from a concrete surface

The condition of the old lining

Pipe openings are a common leak source because groundwater finds the weakest seal point.

Limescale deposits inside a water pipe

Sediment and scale

High internal humidity promotes algae and bacterial growth because ventilation is poor and light limited.

Water pipes passing through a concrete wall

The pipe entries

Salt deposits from wet soil accumulate on walls and floors and damage new coating adhesion.

A metal cover over a water tank opening

The hatch and the vent

Pressure from groundwater cracks the roof if the tank is not properly supported from below.

How we work

  1. 1

    Inspect with the tank empty

    We drain it and read the surface dry: whether the water leaves through a crack, a joint or a pipe collar, and what the outer face of the wall and the ceiling below are telling us. A level test with the valves closed separates a leaking tank from leaking pipework.

  2. 2

    Clean and prepare the substrate

    Sediment out, a high pressure wash, the loose old lining and the weak surface layer of the concrete taken back, then dried. The material grips sound substrate and nothing else.

  3. 3

    Make the cracks and joints good

    Cracks are chased out and filled with a repair mortar, a cove is formed where the floor meets the wall, and every pipe collar is treated on its own.

  4. 4

    Lining, fill test, sterilisation

    Successive coats, each run across the one beneath it, on the face the water touches. Then a full cure, a fill with the level watched, and sterilisation with the first fill run to waste before the tank returns to use.

What water tank sealing includes

  • A technician inspecting with a flashlight

    Finding where the water leaves

    Carried out drained and dry: cracks, joints, pipe collars and the outer face of the wall.

  • A metal floor drain

    Draining and sediment removal

    The last of the water and the settled layer on the floor come out, because a lining does not stick over sediment.

  • A gloved hand applying bait into a joint

    Cracks and joints made good

    The crack opened and filled, a cove formed at the floor to wall junction, and each pipe entry worked separately.

  • A spray nozzle in close detail

    Lining coats on the water face

    More than one coat, each crossing the one below, in material made for drinking water tanks rather than roof waterproofing.

  • A clean kitchen counter after treatment

    Curing, fill test and sterilisation

    The material is left to cure, the tank is filled and the level watched, then sterilised and the first fill run to waste. How long the cure takes follows the material and the weather, and we tell you before the date so you can plan around the supply.

  • The visit report being written on a clipboard

    A follow-up level check

    We come back once it is in service to read the level and check the outer face, because any remaining loss shows up then rather than on the day of the work.

The character of Al Husayniyah

Mixed district: shops at street level with homes above them

The mixed agricultural-residential character means high humidity and unstable soil. Tanks need strong sealing against hydrostatic pressure and an effective drainage system around the building.

Questions about this district

Why does my tank leak from the floor even though the cement is new?

Groundwater from the wadi creates pressure on the floor from outside. This pressure splits small cracks and causes leaks.

Is sealing the walls alone enough or must I seal the floor too?

The floor is most vulnerable because groundwater presses on it constantly. Both floor and walls must be sealed and drainage around the tank improved.

Does Al Husayniyah's wet soil need special preparation before sealing?

Yes, we must improve drainage around the tank first. If groundwater is very high, we may need a sump well or drain system.

Will groundwater affect the seal's durability after we finish?

Yes. If hydrostatic pressure persists, the seal may fail over time. Good drainage around the tank is essential.

How do we tell internal leaks from leaks caused by external pressure?

External pressure leaks start at the floor and lower corners. We measure hydrostatic pressure by drilling test wells around the tank to check groundwater level.

Are new buildings in Al Husayniyah better protected from moisture?

Newer buildings are better but still need professional sealing and drainage. Older tanks in the area face greater risk.

How much does water tank sealing in Al Husayniyah cost?

It is set after the inspection, because the price follows the type of infestation, the size of the space, how far it has spread and the number of visits it needs. Send a photo and a description on WhatsApp and we will give you an estimate before we reach Al Husayniyah.

Nearby districts we cover

Other services in Al Husayniyah

Other services we provide to residents of Al Husayniyah.

All services

Need water tank sealing in Al Husayniyah? Tell us what you saw and we will tell you what it needs

We reach Al Husayniyah at a time we agree, and you get the full cost before we start.

Call now +966 57 336 7012 WhatsApp